Filter Elements

Filter Elements

Vane Pack Mist Eliminators​​ Construction Materials

 ​​ ​​ ​​​​ Stainless steels, Duplex Steels

 ​​ ​​ ​​​​ Alloy C276, 400, 625, 825, 20, etc...

 ​​ ​​ ​​​​ Thermal-set plastics, FRP


Typical Applications

 ​​ ​​ ​​​​ Low Pressure Evaporators

 ​​ ​​ ​​​​ Refinery Vacuum towers

 ​​ ​​ ​​​​ Scrubbers in flue gas desulfurization (FGD) systems

 ​​ ​​ ​​​​ Pulp and Paper mills

 ​​ ​​ ​​​​ Sugar refinery




Vane Pack Mist Eliminators are high capacity separators; they collect essentially 100% of all particles greater than 8 to 40 microns in diameter, depending on design parameters. They are assembled as banks of parallel vane profiles. This design causes the gas to change direction a number of times from inlet to outlet of the separator. The intertia of the liquid droplets forces the entrained liquid droplets to impinge on the vane surfaces where they form a liquid film and drain. Simple Vane Pack profiles are particularly suitable​​ 

for applications with a significant risk of fouling due to solid particles or high viscosity liquids in the feed. Omega Separations offers a wide range of Vane Packs depending on the direction of gas flow and the complexity of the vane profiles. Sectional installation of the vane banks allows installation and removal through the vessel manway.



  • Suitable for applications where solids or sticky and viscous liquids are present and would plug a wire  ​​ ​​ ​​​​ mesh mist eliminator

  • Suitable for both vertical and horizontal gas flow Good collection efficiency in low pressure drop and vacuum applications

  • Suitable for higher liquid and gas loads.


Wire Mesh Mist Eliminators

Construction Materials:

  • Stainless steels, duplex steel

  • Alloy C276, 400, 625, 825, 20, etc...

  • Plastics (PP , FEP , ET FE, ECTFE)

  • Fibrous components (PT FE, Polyester, Glass fibres)


Typical Applications:
There is a very large range of applications which are mainly in the following fields:​​ 

  • Knock-out drums

  • Evaporator systems

  • Scrubbing systems and absorbers

  • Glycol dehydration

  • Gas processing

  • Inert gas scrubbers

  • Sulphuric acid drying towers

  • Sulphur condensers

  • Steam drums

  • Inlet separators

  • Turbo-expander suction drums

  • Dew-point separators

  • Compressor suction drums

  • MS F/ME D desalination

Wire Mesh Mist Eliminators are easy to install cost effective separators that are able to collect liquid particles 2 to 10 microns in diameter with essentially 100% efficiency if designed properly to the process conditions. They are available in almost any size or shape and can be manufactured in a broad range of metals or plastics.

They are produced as multiple layers of knitted mesh making it a dense pack and presenting a large surface area to the droplets entrained in the gas stream. The separation of the droplets is achieved by impingement on, and capture by, the wires of the mesh where the droplets coalesce and drain. Most of the wire mesh mist eliminators are supplied complete with rigid open area support grids allowing direct installation onto support structures such as beams and rings. The mist eliminator is made out of sections allowing easy handling and access through the vessel man ways. Additional accessories such as tie wire, bolting, clamps and support beams can be delivered if needed.


  • High collection efficiency

  • Low installed cost

  • Low pressure drop

  • Fast delivery and service



Coalescing Filter Cartridge


  • High Efficiency Coalescing

  • Completely Disposable

  • Suitable For Corrosive Applications

  • High Flow Rates, Low Pressure Drops

  • Custom Sizes Available

  • Suitable For Highly Adsorbent Gases

  • Gas Or Liquid Service

  • Complete Removal Of Sub-Micron Contaminants


  • Coalescing Filtration

  • Natural Gas

  • Corrosive Gas Filtration

  • Off-Shore

  • Instrumentation

  • Particulate Filtration

  • Natural Gas Vehicle

  • Analytical